标签: 目录VIP认证‖ | 6语种通行,超200个国家买家主动找到你,出海计划从这里开始 | 6语种通行,超200个国家买家主动找到你,出海计划从这里开始 | 6语种通行,超200个国家买家主动找到你,出海计划从这里开始 | 6语种通行,超200个国家买家主动找到你,出海计划从这里开始 | 6语种通行,超200个国家买家主动找到你,出海计划从这里开始
| 加入桌面 | 手机版 | 无图版
高级搜索 标王直达
排名推广
排名推广
发布信息
发布信息
会员中心
会员中心
 

高亮度低光衰晶元芯片3014LED贴片灯珠正发光6-12LM

点击图片查看原图
品 牌: 宇亮光电 
型 号: 高亮度低光衰晶元芯片3014LED灯珠 
规 格: 3.0*1.4mm 
单 价: 0.1元/个 
起 订: 1000 个 
供货总量: 10000000 个
发货期限: 自买家付款之日起 3 天内发货
所在地: 广东 深圳市 宝安区
有效期至: 长期有效
最后更新: 2013-06-22
浏览次数: 344
询价
公司基本资料信息






 
 
产品详细说明

光 通 量:6-12Lm               功       率:0.06W-0.1W
显色指数:70-85RA             发光角度:120度
芯片品牌:晶元                     芯片数量:1芯     
金线材质:99.99%纯金       支架材质:
发光颜色:可以生产各种发光颜色。
色温或波长:可以生产各种色温或波长产品。
发光方式:正发光、侧发光均可以生产。

特       点:小功率、高亮度,发光角度大,低阻抗,散热快。
应用领域:广告招牌,指示灯,led背光源

产品介绍:

产品尺寸图:

PART NO. (型号)
CHIP
Lens Color
Material
Source Color
3014白光
ALInGaP
White(白色)
yellow(黄色)





Notes:
1. .所有单位是毫米(英寸)
2.允许误差为正负0.25mm,除非另行通知。
3.规格可能随时有变化,不另行通知。
4.本数据有效期为六个月

Absolute Maximum Ratings at TA=25℃

Parameter(参数)

Valce(标准值)
Unit(单位)
Power Dissipation(消耗功率)
120
mW
Pilsed  Forward Current(脉冲顺向电流)
(1/10 Duty Cycle, 0.1ms Pulse width
100
mA
Continuous Forward Current
(连续工作电流)
30
mA
Derating Linear From 50℃
(电流比例关系)
0.4
mA /℃
Reverse Voltage(反向电压)
5
V
Operation Temperature Range
(工作温度)
-40℃ to +80℃
Storage Temperature Range
(储存温度)
-40℃ to +80℃
Lead Soldering Temperature
[4mm (.157”) From Body](焊接温度)
260℃ for 5 Seconds(260度下不超过5秒)
Electrical / Optical Characteristics at TA=25℃
Parameter(参数)
Symbol标志
Min. 最小值
Typ. 中间值
Max. 最大值
Unit单位
Test Condition测试条件
Luminous Intensity
(光通量)
  Φ
10
11.5
14
Lm
IF=30mA Note 1.4
Source color(发光颜色)
CCT
6000
 
6500
K
IF=30mA Note4
Viewing Angle
(发光角度)
2θ1/2
115
120
125
deg
Note 2
Forward Voltage
(正向电压)
VF
3.0
3.2
3.4
V
IF=30mA
Reverse Current
(反向电流)
IR
-
-
5
μA
VR=5V
Note1.Luminous intensity is measured with a light sensor and filter combination that approximates the CIE (Commission International De L’Eclairage) eye-response curve.
      2.1/2 is the off-axis angle at which the luminous intensity is half the axial luminous and intensity.
     3.The dominant wavelength, λd is derived from the CIE chromaticity diagram and represents the single wavelength which defines the color of the device.
       4.The IV guarantee should be added ±15%.
                                       特性曲线图
Forward Current                                 Relative Luminous Intensity
IF = f (VF); TA = 25 °C                                     IV/IV(30mA) = f (IF); TA = 25 °C
Reflow Soldering Instructions (回流焊说明)
1.Number of reflow process shall be less than 2 times and cooling
process to normal temperature is required between first and Second soldering process.
(本产品最多只可回焊两次,且在首次回焊后须冷却至室温之后方可进行第二次回焊.)
2.When soldering, do not put stress on the LEDS during heating.(高温焊接时,不能外加压力在LED上.)
3.After soldering,do not warp the circuit board.(焊接完成后,不能弯曲线路板.)
1>Lead Solder(有铅回焊)
Recommended Soldering Patter (n推荐焊盘式样)
(单位:毫米)
0条 [查看全部]  相关评论
 
更多..本企业其它产品

[ 供应搜索 ]  [ ]  [ 告诉好友 ]  [ 打印本文 ]  [ 关闭窗口 ]

 
 
LED贸易网 | 光伏网 | 光电设备网 | 光电人才网 | 光电技术论坛 | LED展会 | LED china | china LED | LED灯出口德国 | LED灯出口西班牙 | LED灯出口阿拉伯 | LED灯出口东欧 | LED灯出口美国 | LED灯出口
购物车(0)    站内信(0)     新对话(0)